newflux
Journal Studio Design

Cabling Plans and Acoustic Layout: How We Set Out a Studio Brief

Tom Pickering

5 min read

Part three of our look at studio design: how layout, acoustics and cabling plans are drawn up together for television and streaming rooms, and what we ask clients to settle first.

Cabling Plans and Acoustic Layout: How We Set Out a Studio Brief

Why the plan starts with cables and walls

Most studio briefs arrive describing cameras, desks and screens. Our first questions are about walls, floors and ceilings, because those decide where cable can run, where sound will bounce and how much room a crew actually has. A studio that looks right on a floor plan can still be awkward to work in if the cable routes cross a doorway or the air handling sits above the presenter.

This part of our studio design work covers the plan that sits between the initial layout and the installation drawings. It brings acoustics and cabling into the same document so that neither is bolted on at the end. In these late autumn weeks, with many teams planning rooms for the new year, it is a good moment to describe how we approach it.

We write for television and streaming spaces of every size, from a single presenter room to a multi-camera floor. The method is the same; only the number of routes and the amount of treatment change.

Acoustics: what the room does to the voice

Acoustic planning begins with listening to the empty room. We note reverberation, flutter between parallel walls, noise from outside and from building services, and how far a voice carries before it blurs. From that we propose treatment that suits the use: absorption where reflections hurt speech, diffusion where a room would otherwise sound dead, and isolation only where outside noise genuinely reaches the microphones.

We prefer to treat what the room needs rather than cover every surface. Heavy treatment costs money and floor space, and an over-damped studio makes presenters sound strained and uncomfortable. A balanced room is easier to mix, easier to light and kinder to the people working in it for long shifts.

Sets matter too. Hard flats, glass and screens change the sound of a space once they are installed, so we ask for the set drawings before finalising any treatment.

  • Measure the empty room before choosing treatment
  • Check noise from ventilation, lifts and neighbouring rooms
  • Review set materials that will reflect sound

Cabling: routes, separation and room to grow

A cabling plan names every run: where it starts, where it ends, what it carries and how it gets there. We separate power from signal, keep audio away from sources of interference, and leave clear labelling conventions so that an engineer arriving months later can follow the system without guessing.

Routes need to suit the building. Floor trunking, ceiling trays and wall boxes each have limits on bend radius, fill and access. We mark them on the drawings alongside the equipment positions, so installers see the whole picture and the studio team knows what can be reached without moving furniture.

We also plan spare capacity. Studios gain cameras, monitors and intercom points over time, and an extra conduit laid at the start costs far less than opening a floor later.

  • Separate power and signal routes
  • Label both ends of every run
  • Leave spare conduit for later additions

Layout: where people and equipment actually move

Layout comes from watching how a programme is made. We ask who walks where during a show, where the director sits, how the floor manager reaches presenters, and where cameras need to travel. The plan then keeps those paths clear of cable and stands, and places the control room, or the control corner in smaller spaces, where the director can see and hear what matters.

Sightlines matter as much as floor area. A compact studio with clean sightlines between the director, the talent and the cameras often works better than a larger room with awkward corners. We draw these lines on the plan so they can be tested before anything is built.

For streaming rooms that double as meeting spaces, we also plan how the room reverts to ordinary use without leaving trailing cables behind.

What we ask you to settle before drawing begins

Good drawings need decisions from the client, and we try to ask for them early. The first is the intended programme types: talk, news, music, remote guests. The second is the crew size on a normal day and on the busiest day. The third is the building: who owns it, what may be altered and what services already run through it.

We also ask for a realistic budget range and the date the room needs to be in use. These shape the proposal more than any equipment list, because they decide how much treatment, cable and flexibility is sensible. If some answers are unknown, we say so in the plan and mark the assumption openly.

Where a site visit is possible, we take photographs and measurements ourselves rather than relying on drawings supplied by others.

  • Programme types and crew size
  • Building constraints and permissions
  • Budget range and the date the room must be ready

What you receive at the end

The result is a written plan with drawings: a floor layout showing equipment, sightlines and movement; an acoustic note describing the proposed treatment and the reasoning behind it; and a cabling schedule listing runs, routes and labels. Each document refers to the others, so a change in one is easy to trace through the rest.

The plan is written for people other than us. Installers, facilities managers and the studio crew should all be able to read it and understand what is intended. We are happy to walk a team through it in person, and to answer questions from contractors while the work is under way.

It does not replace specialist construction advice where structural changes are involved, but it gives everyone the same starting point.

A studio plan works when layout, acoustics and cabling are settled together and written down in terms the whole crew can follow. If you are planning a new room or reworking an existing one, the contact page is the place to start, and we will reply with the questions we need answered before drawing anything.