Conventional Fixtures or LED Wash: Choosing a Rig for a Winter Studio
Oliver Hartley
6 min read
Oliver compares a conventional tungsten-halogen rig with an LED wash rig for a small studio or venue stage, weighing colour quality, power, heat and cost, and ends with a recommendation.
The choice in front of most studio managers
When a studio, venue or festival stage plans a new lighting rig, the first real decision is rarely about the plot. It is about which type of fixture will fill it. In practice the two options are a conventional rig built around tungsten-halogen lanterns, and a rig of LED fixtures with colour mixing built in. Both can light a presenter well, and both are in daily use across the country. I am writing this in late autumn, when many of our clients are reviewing budgets and deciding what to install before the busy winter programme begins. So this comparison is aimed at a small to mid-sized room: a studio of modest floor area, a venue stage with a fixed rig, or a festival tent that is rigged and struck within days.
I will compare the two on five points: the quality of light on skin and fabric, power and heat, flexibility on the day, maintenance, and cost over several years. At the end I give a plain recommendation, with the cases where I would still choose the other option. None of this replaces a lighting plot for your own room, which depends on ceiling height, rigging points and what you shoot.
Light quality and colour
Tungsten-halogen lanterns produce a continuous, warm spectrum, and skin tones look natural under them without much correction. Dimming is smooth, and the colour shifts gently towards amber as the lamp fades down, which many directors like. For a presenter in a fixed seat, a well-aimed conventional key light is still hard to fault.
LED fixtures have improved a great deal, but quality varies widely between models. Good units with several emitter colours render skin well; cheaper ones can leave a faint green or magenta cast that shows up on camera even when the eye does not notice it. Always test a fixture on your own cameras, at your usual exposure, before buying a full set. Look at faces, wood, fabric and any branded colours the set uses.
- Check skin tones on the actual cameras you use, not on a monitor in a showroom
- Compare dimming at the low end, where cheap LEDs often step or flicker
- Judge fixtures at your normal working exposure
Power, heat and the room itself
This is where the two options part ways most clearly. A conventional rig draws a lot of current and turns most of it into heat. In a small studio that means air conditioning working harder, presenters who feel the warmth on their faces, and a power supply that may need upgrading before you can run a full set of lanterns together. LED fixtures draw a fraction of that power for comparable output.
The room stays cooler, circuits are less loaded, and a venue with limited supply can often run a complete rig from a modest distribution board. For a festival stage on generator power, the saving is practical rather than theoretical: smaller generators, shorter cable runs, fewer risks. Heat also matters for safety, because hot lanterns near drapes, scenery or a low ceiling need careful clearances that LEDs largely avoid.
Flexibility on the day
Colour changing is the strongest argument for LED. A single wash fixture can serve as a neutral key in one programme and a deep blue backdrop in the next, with the change stored and recalled in seconds. For venues hosting different acts through a week, or studios that rebrand sets between shows, this saves a great deal of re-rigging time and gel changes.
Conventional lanterns win where the job is fixed and simple. A single warm key, a fill and a backlight set once and left alone need no control complexity, and any technician can understand the rig at a glance. They also tolerate being dimmed from basic desks. LED rigs need a little more care with control addressing and fixture modes, and someone on the crew should be comfortable with that before the first show.
Maintenance and cost over time
Conventional lamps have a short life and need regular replacing, and each replacement is a small job at height. Over a few years the lamp bill and the time spent on ladders add up. The fixtures themselves are cheap to buy and easy to repair, and spares are widely available. LED fixtures cost more up front, sometimes several times as much per unit, but the light source lasts far longer and the electricity bill is lower.
For a room used most days, the extra spend is usually recovered within a few years. For a space used only a few times a month, the sum is closer, and a mixed rig can be a sensible compromise. Budget also for the control desk and any data cabling, which LED rigs need more of.
- Conventional: lower purchase price, regular lamp changes, higher running cost
- LED: higher purchase price, little routine maintenance, lower running cost
Our recommendation
For most small studios and multi-use venues, I recommend an LED-based rig, with one or two conventional lanterns kept as key lights where skin tone matters most. That mix gives you the cool running and flexibility of LED for backgrounds and washes, and the familiar warm quality of tungsten where a face is the subject.
I would stay fully conventional for a single-purpose set that rarely changes, or where the budget is very tight and the power supply is already generous. I would go fully LED on generator power, in low-ceilinged rooms, or anywhere the rig changes often. Whichever you choose, test on camera first, and draw the plot before ordering a single fixture.
The right rig is the one that suits how your room is actually used. LED wins on power, heat and flexibility, and conventional lanterns still earn their place for faces and fixed sets. A mixed rig is often the sensible answer. Test fixtures on your own cameras, check your power supply, and have the plot drawn before you buy, so the equipment fits the room rather than the other way round.