newflux
Journal Studio Design

Planning a Small Television Studio: Layout, Acoustics and Cabling

Hannah Doyle

5 min read

A practical walk through the first decisions in studio design: how to arrange the floor, treat the room for sound and plan cable runs so the space still works as the production grows.

Planning a Small Television Studio: Layout, Acoustics and Cabling

Start with the programme, not the room

Every studio plan I have worked on began with the same question: what will be made here in a normal week? A single presenter on a sofa, a three-person panel and a cooking demonstration each ask different things of the floor, the walls and the ceiling. Write down the formats, the number of people in shot, how many cameras you expect and how long a typical recording runs.

Then measure the room properly. Record length, width and ceiling height, and note every door, window, radiator and fixed pillar. Mark the positions of power outlets and any existing data points. A rough sketch to scale on squared paper is more useful at this stage than any software, because it lets you move things about freely.

Be honest about the limits of the space. A room under four metres across can host a good interview or news set, but it will not take a wide drama set. Deciding this early saves expensive compromises later.

  • List the formats you will record
  • Count people in shot and cameras
  • Measure the room, including fixed obstacles
  • Mark existing power and data points

Laying out the floor

Divide the floor into three zones: the set, the camera area and the circulation space. The set needs distance from the walls, ideally at least two metres, so that you can light it from behind and keep the background clear of reflections. The camera area should allow operators to move without stepping on cable or crossing the talent.

Leave a clear route from the door to the set that does not pass in front of a camera during recording. Presenters, guests and crew will come and go, and a studio with a single awkward entrance quickly becomes noisy and slow.

Keep the control position away from the set if you can. Even a corner screened by a heavy curtain helps, since the people watching monitors and talking on intercom should not be audible on the microphones.

A studio that sounds boxy or echoing will cost you in every recording. Hard parallel walls, bare floors and glass are the usual culprits. The aim is not a dead room but a controlled one, where speech is clean and the reverberation does not smear words together.

Start with absorption on the walls behind the cameras and at the first reflection points either side of the set. Thick mineral wool panels in fabric frames work well and can be moved as the layout changes. Add a heavy rug or acoustic flooring beneath the set, and consider drapes along one long wall to give you adjustable damping.

Do not forget noise coming in. Air handling, fluorescent ballasts, lift motors and traffic can all find their way onto a microphone. Walk the room at recording volume with a good pair of headphones and listen before anything is built.

  • Absorb behind cameras and at side reflections
  • Soften the floor beneath the set
  • Check air handling and mains hum before building

Planning cable runs early

Cabling is the part most often left until the end, and it is the part that causes the most trouble when the studio is busy. Decide where signals will start and finish: camera positions, microphone points, lighting dimmers, monitors, intercom and the control position. Then plan the shortest tidy routes between them.

Separate mains power from audio and data wherever you can, and cross them at right angles when they must meet. Mixing the two along a long run is a common cause of hum. Label both ends of every cable with the same short code, and keep a simple drawing that matches.

Install more than you need. Spare conduit, a few extra camera points around the walls and capacity in the patch panel cost very little during the build and a great deal afterwards.

  • Separate power from audio and data
  • Label both ends of each cable identically
  • Fit spare conduit and extra wall points

Lighting grid and power

Although lighting is its own discipline, the studio design must leave room for it. Decide on a grid or rigging bars early, check that the ceiling can carry the weight, and confirm the height gives enough angle to light faces without shining into camera lenses.

Calculate the electrical load before ordering equipment. A set of modern lamps draws far less than older tungsten units, but dimmers, monitors, computers and air conditioning all add up. Speak to your electrician about dedicated circuits for lighting and a separate clean supply for audio.

Think about heat as well. A small room with the door closed and several lamps running will warm up quickly, which affects both comfort and equipment.

Testing before you commit

Before anything is fixed to a wall or ceiling, run a rehearsal in the empty room with temporary furniture, borrowed lamps and a single camera. Walk through a full recording as if it were real, including arrivals, a guest change and a pause for a retake.

Record a few minutes of speech and play it back on headphones and on speakers. Listen for echo, boom and any buzz. Take stills from the camera at each key position and check that the background is clean.

Notes from this session are the most valuable thing you will have when finalising the plan. Small changes at this point are cheap, and the same changes once the studio is built are not.

A good small studio is rarely the result of expensive equipment. It comes from knowing what you will record, giving the floor sensible zones, treating the room for sound and laying cable with room to grow. Take the time to measure, sketch and rehearse in the empty space. If you would like a second opinion on a plan, we are glad to look at it with you.